Last Updated on September 4, 2023 by Thomas James
If you’ve ever changed a tire, you’ll agree it takes work. Changing a tire without a jack requires you to do some things typically reserved for professionals in the field.
Even if you’re a seasoned driver, changing a tire without a jack can be challenging. This blog will look at how to change a tire without a jack and make it easier.
Brakes are a vital part of vehicle safety. But sometimes, the need to change a tire can happen in the most unexpected places. You can still change a tire yourself if you don’t have a jack. It may seem daunting, but it’s easier than you think.
It’s easy to ignore it and take it for granted. Yet, if you’ve ever been involved in a car accident, you’ll know that the jack is vital to getting your car back on the road.
How To Change A Tire Without A Jack
It’s easier than you might think. With a little practice, you’ll change a tire without a jack in no time. Before you begin, you must ensure you have the right tools for the job. If you don’t have a spare tire, you must purchase one.
You’ll Need:
- A flat-soled spare tire
- A jack
- New tire
- pump
- lug nut remover
- lug wrench
- A lug nut puller
- A jack stand
Step 1: Find the Right Tire
First, you need to find the right tire for your vehicle. It can be tricky. Some vehicles are equipped with special tires that have a built-in jack.
You can find these tires in your local tire shop’s “specialty” section. You’ll also need to find a tire that’s the right size for your vehicle.
Step 2: Remove the Old Tire
If you don’t have a jack, you’ll need to remove the old tire before changing the new one. You can use a lug nut remover or a lug nut wrench. If you have a jack, using a lug nut remover is good. The lug nut remover will help you remove the nuts without damaging the tire.
Step 3: Put the New Tire on
Once you’ve removed the old tire, you’ll need to put the new tire on. It is easier than it sounds. You can use it to raise the car if you have a jack. You’ll need to lower the car again to put the tire on. If you don’t have a jack, you must lower the car by hand.
In any case, you’ll need to put the tire on at the right angle. If you put the tire on too high, you’ll have to take the tire off and start over. If you put the tire on too low, you’ll have to put the tire back on again.
Step 4: Put the Lug Nuts on
Once you’ve positioned the tire, you must put the lug nuts on. You’ll need to use a lug nut wrench to do this. Apply WD-40 to help the lug nuts tighten. When replacing the lug nuts, you can use a star screwdriver to ensure the nuts are tightened equally. Once you’ve put the lug nuts on, you must tighten them up. You’ll want to tighten them up as much as possible. It will make it easier to change the tire.
Remove any blocks or wheel chocks from behind the tires on the opposite side.
You have now changed your tire without using a jack. Remember to check the tire pressure of the spare tire you installed with the tire pressure gauge. Following a tire change, you may also need to reset the TPMS in your vehicle.
How To Change A Tire Without A Jack: Digging the Ground Method
This method is also easy to use. It’s similar to the previous process but easier to do. It’s more challenging than it may seem, but you can do it. You’ll need to dig the ground. It is to make sure the ground is level. You’ll need to dig the hole big enough for the tire. You can use a pry bar if you don’t have a jack.
- Drive slowly until the tire to be changed is over open soil. After parking, engage the emergency park brake.
- Find a stump or a piece of concrete and slide it beneath the axle nearest the tire to be changed.
- The blocking materials can then be stacked until they contact the axle.
- Remove the soil beneath the flat tire. You have three options: use your hands, a tire iron, or a stick.
- Continue until the axle is firmly supported by the materials used to block it. Dig a few inches down on all four sides of the tire.
- Ensure the hole is large and deep enough to accommodate changing the tire.
- Using a tire iron, remove all of the tire nuts.
- Pull the rim away from the studs and remove the flat tire from the hole.
- Install the spare tire on the studs until it reaches the rim holes.
- Tighten all of the nuts with the tire iron.
Why is it necessary to change a tire?
- For instance, the ground may be uneven. You may be driving over a pothole. Or, you may be driving over a patch of loose gravel.
- The more you drive on your tire, the more the tread wears down, making it increasingly smooth and reducing humidity.
- The thin tread is vulnerable to total failure when stretching when driving on wet roads with worn tires.
- By diverting water from beneath the tire, good tires are supposed to allow you to tread on wet surfaces. It increases traction on wet roads and lowers the risk of slipping.
- On the other hand, you may be driving over a piece of concrete. You may also be driving over a curb.
Final Thoughts
We hope you enjoyed our blog about changing a tire without a jack! The title is obvious, but we know that everyone sometimes runs into a situation where they can’t get a car out of the mud without a jack.
We want to make sure that you’re prepared for these moments. If this is the case, we hope you remember to grab a few things before leaving the house to make the process go smoothly. Thank you for reading. We would love to hear from you!
