How To

How To Bypass Ignition Switch To Start Car?

Last Updated on July 25, 2022 by Thomas James

Sometimes you just need to get around a car blocking your driveway, but the car won’t start. If you’re going to get around the car, you’ll need to bypass the ignition switch to start the car, which can be a tricky process. This blog will give a few helpful tips on how to bypass ignition switch to start car.

Car troubles can be tough to deal with, especially in the middle of the night. But, if you know how to bypass the ignition switch, you can get your car started and get moving. You may be able to start your car by bypassing the ignition switch. If you have a service manual for your vehicle and some essential tools, you can bypass the ignition switch to start your car. You can also bypass the start switch to start your car with a button push. It is good if you don’t want to wait for the battery to charge.

How To Bypass Ignition Switch To Start Car

What is the Ignition Switch?

The ignition switch is the part of the car that turns on and off the car. It is located in the center of the steering column and has two wires connected to it. The switch turns on and off the car by turning the ignition key. The ignition switch is turned on when you turn the key to the “on” position.

You also, like: How To Quiet A Noisy Car Ac Compressor?

Ignition System Warning Signs

If your car is running fine but won’t start when you turn the ignition key, there are a few warning signs that your ignition system is terrible. If you notice any of these warning signs, you should consider bypassing your ignition switch. Warning Signs of Ignition System Problems:

  • Your car won’t start when you turn the ignition key.
  • A car will start and run fine for a few minutes but then stop running.
  • Your car starts, but the engine will not turn over.

Hard to turn the key to start the car

If the key still works, you may notice that it does not turn smoothly every time you decide to start the car. The key may be scuttling or stuck inside the keyhole. The ignition switch has been severely damaged and requires immediate attention before things worsen.

Trouble in starting the car

It is the result of a failed ignition switch. If the ignition switch is damaged, it won’t work correctly and will cause your car not to start. If you notice any of the warning signs listed above, you should have your ignition switch bypassed as soon as possible.

No starter motor sound when you turn the key

If you have a car with a starter motor, you should hear the starter motor noise when you turn the key to the “on” position. If you don’t hear a starter motor sound, you may have a problem with the ignition switch. You should consider having your ignition switch bypassed.

Stalling Vehicle

If your car suddenly shuts down while driving with no warning, you may have a problem with the ignition switch.

Stuck steering wheel

If your steering wheel doesn’t move, it may result from a failed ignition switch.

Check Engine Light

If your car has a check engine light on, it could mean that the ignition switch is damaged.

How to Bypass Ignition Switch to Start Car

If you have trouble starting your car, the ignition switch may be damaged. If you have a service manual for your car, you can bypass the ignition switch to start your car. If you don’t have a service manual, you can also bypass the ignition switch by following these steps.

Tools Needed to Bypass the Ignition Switch

To bypass the ignition switch, you will need a set of essential tools. It would be best if you had the following tools on hand:

  • A car battery.
  • A wire connector.
  • A screwdriver.
  • A pair of needle-nose pliers.
  • A flashlight.

Hotwiring

The first step is to remove the ignition switch. It is the part that turns on and off the car. The switch is located in the center of the steering column and has two wires connected to it.

If you’ve older cars built before the mid-1990s, this method may work for you. Locate the steering wheel column once inside the vehicle. Remove the plastic cover that protects all internal components. It should reveal all necessary components.

Then, look for the wiring harness connector. Because there are so many cables and wires in this area, it may be challenging to find the specific connector. However, it is usually found in the center of the steering column. Other wires, cables, and connectors are associated with the lights.

You must locate the connectors for the battery, ignition, and starter.

The yellow and brown wires are connected to the ignition. The red ones go with the battery. Strip an inch of insulation from the battery wires and twist them together.

Connect the ignition on/off the wire to the battery wire, and the lights will turn on, and the electrical parts will begin to work. Cut the starter wire half an inch short and connect it to the battery wires to start the engine. Now it’s time to start the engine.

The Screwdriver

The next step is to use a screwdriver to loosen the screws on the ignition switch. You should remove the ignition switch, but you may need to remove the cover.

This method may also work, but be cautious because it has the potential to wreck the ignition switch. It will also teach you how to start a car that has a broken ignition switch. Then, as if it were a key, insert the screwdriver into the keyhole and turn the ignition to start the car.

Jumper Cables

If you are unable to start your car, you may have a damaged ignition switch. To bypass the ignition switch, you will need jumper cables. Connect the battery’s positive terminal to the positive terminal of the ignition switch. You should use the positive terminal because it’s usually the most current terminal. The solenoid will be activated, and the car should start.

How to Check if the Ignition Switch Works

Multimeter Test

An ignition switch powers your car’s ECU and ignition coil. It means your ignition switch has two wires coming out of it.

  • Place the ignition switch in the off position when using a multimeter.
  • Switch the power feed wire with the positive probe of the multimeter and the negative wire with any unpainted metal in your car.
  • Next, try to kickstart the engine while keeping an eye on the multimeter reading.
  • If the voltage reading is less than 90% of the battery voltage, you have a faulty ignition system.

Light Test

A 12V test light can be used in the absence of a multimeter.

  • Turn the key off and disconnect the module’s cable connector from the starter solenoid’s terminal. It prevents your car from starting when the key is turned to the on position.
  • Return to the start position with the key.
  • The red wire should be connected to the ignition coil battery post and the test voltage.
  • Connect the white wire from the ignition switch to the start position.
  • The lamplight will turn on if your ignition switch is working correctly. Otherwise, you have a bad ignition switch.

Final Thoughts

We hope you enjoyed our article on how to bypass ignition switch to start car. It is a great place to start if you have ever had the unfortunate experience of not being able to start your vehicle no matter what you try. It is a handy guide, especially if you have a manual transmission car. Thank you for reading! We hope that if you ever have to try this DIY solution, you will be able to bypass the ignition switch to start the car.

Thomas James

Thomas James is an experienced auto mechanic who enjoys writing comprehensive guides and offering valuable tips on various car issues.

Related Articles

Back to top button